APH techniek

All data are considered to be unbinding reference values. We accept no liability for data selection that is not confirmed in writing. Pressure data refer, if not otherwise indicated, to liquids of Group II at +20°C. 9 L SW Accessories for compressed air tools Inline filters up to 2800 l/min. Type FT/FT Type FT/MT Thread Flow* approx. L SW iLF 18 iLF 18 iA G 1 / 8 “ 600 l/min. 36 17 iLF 14 iLF 14 iA G 1 / 4 “ 1250 l/min. 42 19 iLF 38 iLF 38 iA G 3 / 8 “ 2100 l/min. 54 24 iLF 12 iLF 12 iA G 1 / 2 “ 2800 l/min. 62 30 * at 6 bar input pressure Application: Filter for direct installation in a compressed air line, a hose or directly before a compressed air tool Materials: Housing: Brass nickel-plated, filter: Sintered bronze, seals: NBR Temperature range: 0°C to max. +80°C Input pressure: Max. 12 bar, filter porosity: 36 µm type FT/MT type FT/FT L SW Type BLP DR 20 G 1 / 4 “ 1.5/2.0/2.5 BLP DR 30 G 1 / 4 “ 2.2/2.9/3.5 BLP DR 40 G 1 / 4 “ 2.8/3.7/4.5 BLP DR 50 G 1 / 4 “ 3.5/4.6/5.4 1) ± 0.6, 2) ± 0.5 bar, 3) ± 0.2 bar Blow guns pressure reducing valves Materials: Housing: Brass, seal: NBR Input pressure: Max. 15 bar Advantages: Ÿ Tool machines are not damaged, since chipping is not are not depressed in sensitive areas (seals, lathe chuck, machine bed, etc.) Suitable: Only for compressed air i n put pressure m ax. 15 bar output pressure 2-8 bar ü Type BLP DR 60 G 1 / 4 “ 3.8/5.0/6.0 BLP DR 70 G 1 / 4 “ 4.8/6.2/7.3 BLP DR 80 G 1 / 4 “ 5.5/7.3/8.2 Warning: When relieving the primary side, the secon- dary side is not vented! Special pressure regulator for com- pressed air tools (vent on secondary side) can be found above. 34 52 SW 17 Inline pressure regulators 700 l/min.* Function: Not resettable, preset diaphragm pressure regulator Materials: Housing: Zinc die-casting, internal parts: Brass, stainless steel, seals: NBR Temperature range: 0°C to max. +60°C Input pressure: Max. 18 bar, media: Compressed air, nitrogen, neutral gas Advantages: Ÿ The pressure which has been set cannot be altered ü Type Thread Output pressure Press. tolerance iLDR 14-1 G 1 / 4 “ 1 bar ± 0.3 bar iLDR 14-2 G 1 / 4 “ 2 bar ± 0.3 bar iLDR 14-3 G 1 / 4 “ 3 bar ± 0.3 bar iLDR 14-4 G 1 / 4 “ 4 bar ± 0.4 bar iLDR 14-5 G 1 / 4 “ 5 bar ± 0.5 bar iLDR 14-6 G 1 / 4 “ 6 bar ± 0.6 bar iLDR 14-7 G 1 / 4 “ 7 bar ± 0.7 bar iLDR 14-8 G 1 / 4 “ 8 bar ± 0.8 bar * at 7 bar input pressure Description: The inline-pressure regulators are screwed directly into the tool to turn down the working pressure to a value that is optimal for the tool. The pressure regulators are distinguished by their low weight (approx. 40 g), high flow performance (up to 800 l/min*), and an automatic relieving system . Materials: Housing: Aluminium, seal: NBR Temperature range: 0°C to max. +80°C Input pressure: Max. 25 bar Advantages: Ÿ A piece of compressed air equipment uncoupled from the compressed air line is immediately fully vented, unlike blow gun pressure reducing valves. This removes the risk of injury from accidental re- lease of an uncoupled pneumatic nail gun, for example. Ÿ The pressure which has been set cannot be altered. Suitable: Only for compressed air Pressure regulators for compressed air tools up to 800 l/min.* ü 59 10 i n put pressure m ax. 25 bar output pressure 2-8 bar 19 Type TOOL DR 20 G 1 / 4 “ 500 l/min. 2 bar TOOL DR 30 G 1 / 4 “ 550 l/min. 3 bar TOOL DR 40 G 1 / 4 “ 600 l/min. 4 bar * at 12 bar input pressure, Δ p=0.5 bar Type TOOL DR 50 G 1 / 4 “ 650 l/min. 5 bar TOOL DR 60 G 1 / 4 “ 700 l/min. 6 bar TOOL DR 80 G 1 / 4 “ 800 l/min. 8 bar Inline lubricators for compressed air tools Pressure range: Max. 6.3 bar Note: For compressed air equipment with heavy vibrations, we recommend connecting the lubricator to the device with a short piece of hose. Advantages: Ÿ This lubricator is used directly on the compressed air tool. Through the short path from the lubrica- tor to the device, a constant supply of oil is guaranteed. The fill level is always visible. ü Type Input (FT) Output (MT) Air permeability Oil supply PT 1025 Rp 1 / 4 “ R 1 / 4 “ Approx. 860 l/min 20 ml after decoupling no residual pressure in the tool Saves air - protects machine Thread (FT/MT) Flow* approx. Output pressure ( ± 10 %) Thread (FT/MT) Output pressure at input pressure 5 bar 1) /10 bar 2) /15 bar 3) Thread (FT/MT) Output pressure at input pressure 5 bar 1) /10 bar 2) /15 bar 3) Thread (FT/MT) Flow* approx. Output pressure ( ± 10 %) 540 APH Techniek BV - Wateringen - T +31 (0)174 219 200 - sales@aphtechniek.nl - www.aphtechniek.nl