APH techniek

All data are considered to be unbinding reference values. We accept no liability for data selection that is not confirmed in writing. Pressure data refer, if not otherwise indicated, to liquids of Group II at +20°C. 4 Tubes Rod length: 5 m Copper installation tubes in rods, hard (R 290) , semi-hard (R 250) DIN EN 1057/DVGW Strength CUR 4x1* 4 1 R 290 382 bar CUR 6x1 6 1 R 290 229 bar CUR 8x1 8 1 R 290 163 bar CUR 10x1 10 1 R 290 127 bar CUR 12x1 12 1 R 250 104 bar CUR 14x1* 14 1 R 290 89 bar CUR 14x1.5* 14 1.5 R 290 135 bar CUR 15x1 15 1 R 250 82 bar CUR 16x1* 16 1 R 290 76 bar CUR 16x1.5* 16 1.5 R 290 116 bar CUR 18x1 18 1 R 250 67 bar CUR 22x1 22 1 R 250 54 bar CUR 28x1 28 1 R 250 42 bar CUR 35x1.2 35 1.2 R 290 41 bar CUR 42x1.2 42 1.2 R 290 34 bar CUR 54x1.5 54 1.5 R 290 33 bar When ordering, please state shipping length! Parcel service: max. 2 m Express: max. 3 m Freight: max 6 m * industrial quality EN 12449, ** the maxi- mum permitted operating pressure was based on the use of soft copper tubes (R 200) and a safety value of 3.5 at an operating tempera- ture of +100 °C. The permitted operating pressure is based on the copper tube, not on the connecting parts! The values for harder tubes are higher. Copper installation tubes in rings, soft (R 220) DIN EN 1057/DVGW CUR 4x1 R* 4 1 50 m 382 bar CUR 6x1 R 6 1 50 m 229 bar CUR 8x1 R 8 1 50 m 163 bar CUR 10x1 R 10 1 50 m 127 bar CUR 12x1 R 12 1 50 m 104 bar CUR 15x1 R 15 1 50 m 82 bar CUR 18x1 R** 18 1 25 m 67 bar CUR 22x1 R** 22 1 25 m 54 bar * industrial quality EN 12449 (R 200), ** only complete rolls are available, *** the maximum permitted operating pressure was calculated based on soft copper tubes (R 200) and a safety value of 3.5 at an operating temperature of +100 °C. The permitted operating pressure is based on the copper tube, not on the connecting parts! The values for harder tubes are higher. Threaded tubes DIN EN 10255-M (DIN 2440) Description: Tube made of non-alloy steel, suited for welding and tapping Operating range: Transport of liquids, air and non-hazardous gases Version: Black finish or hot-dip galvanised, with smooth tube ends without thread or sleeve (OO) Materials: S 195 T (ST 33), all tubes are subjected to cold-water pressure testing or eddy-current testing under 50 bar Operating pressure: Liquids up to max. 25 bar, gas and compressed air up to max. 10 bar Manufacturer lengths: 6 m ± 0,15 m (seamless ± 1 m) GWR 14 G --- GWR 14 V G --- 1 / 4 “ 13.5 2.35 GWR 38 G GWR 38 GWR 38 V G GWR 38 V 3 / 8 “ 17.2 2.35 GWR 12 G GWR 12 GWR 12 V G GWR 12 V 1 / 2 “ 21.3 2.65 GWR 34 G GWR 34 GWR 34 V G GWR 34 V 3 / 4 “ 26.9 2.65 GWR 10 G GWR 10 GWR 10 V G GWR 10 V 1“ 33.7 3.25 GWR 114 G GWR 114 GWR 114 V G GWR 114 V 1 1 / 4 “ 42.4 3.25 GWR 112 G GWR 112 GWR 112 V G GWR 112 V 1 1 / 2 “ 48.3 3.25 GWR 20 G GWR 20 GWR 20 V G GWR 20 V 2“ 60.3 3.65 GWR 212 G GWR 212 GWR 212 V G GWR 212 V 2 1 / 2 “ 76.1 3.65 GWR 30 G GWR 30 GWR 30 V G GWR 30 V 3“ 88.9 4.05 GWR 40 G GWR 40 GWR 40 V G GWR 40 V 4“ 114.3 4.50 When ordering, please state shipping length! Parcel service: max. 2 m Express: max. 3 m Freight: max 6 m Tube Ø external Operating pressure*** Wall thickness Ring length Type copper Tube Ø external Operating pressure** Wall thickness Type copper Tube Ø external Thread size Wall thick. Type welded black Type seamless black Type welded hot-dip galv. Type seamless hot-dip galv. Tube cutter Suitable: For cutting of aluminium, copper, steel and stainless steel pipes, as well as plastic and composite pipes. Pipe cutter with 4 guide rollers for optimum holding of the pipes, incl. replacement cutting wheel in the handle. Do not use to cut tubes for cutting ring fittings! Note: Type Ø 6 - 76 mm only has a practical quick adjustment. The pipe cutters are colour coded: red - for copper, brass & aluminium pipes grey - for steel & stainless steel pipe black - for plastic & composite pipes Type Type max. wall Ø 3 - 35 mm Ø 6 - 76 mm for material thickness RAS 35 RAS 76 Copper, brass, aluminium 2 RAS 35 ES RAS 76 ES Steel, stainless steel 2,5 --- RAS 76 KU Plastic, composite pipes 8,6 Type Replacement cutting wheel Ø x width RAS KL 19 x 6,2 RAS KL ES 19 x 6,2 RAS KL KU 30 x 6,2 Ø 3 - 35 mm Ø 6 - 76 mm Type Design for tubes Ø external ENTGR 36 Standard 4 - 36 ENTGR 35 ES Heavy Duty 8 - 35 ENTGR 56 ES Heavy Duty 10 - 56 Deburrer Materials: Standard: Plastic body with stainless steel blades, Heavy Duty: Aluminium with black stainless steel graters Suitable: For deburring (inside and outside) of pipes. Standard design can be used for soft materials, such as plastic, copper, aluminium, etc. Heavy Duty design is suitable also for steel and stainless steel. Standard Heavy Duty APH Techniek BV - Wateringen - T +31 (0)174 219 200 - sales@aphtechniek.nl - www.aphtechniek.nl 251