APH techniek

All data are considered to be unbinding reference values. We accept no liability for data selection that is not confirmed in writing. Pressure data refer, if not otherwise indicated, to liquids of Group II at +20°C. 4 Band-It - The power clamp Width Thickness C133 9.5 mm ( 3 / 8 “) 0.38 mm 2000 N C134 12.7 mm ( 1 / 2 “) 0.38 mm 2670 N C135 15.9 mm ( 5 / 8 “) 0.38 mm 3338 N C136 19.1 mm ( 3 / 4 “) 0.38 mm 4005 N * packing unit: 100 unit Band-It tapes Type Valustrap C153 C154 C155 C156 Application: For light loading, e.g. sign fastener, cable bundling, (not recommended for hose connections) Assembly tool: C001, C003, C075 (can be found on page 241) Assembly: See example at the top of this page Materials: Rust-free, austenitic stainless steel with fully rounded edges Width Thickness C202 -- 6.4 mm ( 1 / 4 “) 0.51 mm --- C203 C203Y 9.5 mm ( 3 / 8 “) 0.64 mm Yellow C204 C204B 12.7 mm ( 1 / 2 “) 0.76 mm Blue C205 C205G 15.9 mm ( 5 / 8 “) 0.76 mm Green C206 C206R 19.1 mm ( 3 / 4 “) 0.76 mm Red * packing unit: 100 pcs., ** design similar to Valustrap Band-It tapes Type 201 C252** C253 C254 C255 C256 ü Especially good value! Especially strong! Pull the buckle with ears to the tape end on the tape. Form clamps and place tape on tape. Pull the buckle over both tapes and bend the tape end approx. 30 mm under the buckle. When there are high loads on the clamps (e.g. for hose assembly) pull the tape twice through the buckle. Insert tape in the clamping tool from the side, press on the cam lever and tighten the crank clamps by rotating them. The maximum tension is rea- ched when the tape can no longer be pulled under the buckle (this is easily "fulfilled" by applying a finger). After reaching the required tension, bend the tool slowly over the buckle. At the same time, loosen the crank by approx. a half rotation in order to pre- vent loss of tension and cracks in the tape. In order to crop the tape, pull the cutting lever backwards. Hit the tape onto the buckle with the hammer and fold both buckle ears over to secure the tape end. Band-It - assembly example Type Width C720 6.4 mm ( 1 / 4 “) 2225 N 50 unit C722 9.5 mm ( 3 / 8 “) 4005 N 50 unit C724 12.7 mm ( 1 / 2 “) 6675 N 25 unit C726 19.1 mm ( 3 / 4 “) 10013 N 25 unit Band-It scru-lokt buckles Type 201 Application: For the manufacturing of clamps that can be retightened, along with "type 201" straps Assembly tool: C001, C003 (can be found on page 241) Assembly: Like in the example on top of the page, however, the strap is not bent after tension, but rather fixed with the hexagon socket screw. In order to allow further tension, the tape should protrude approx. 100 mm from behind the loop. Warning: Avoid injuries caused by folding the end of the loop! Materials: Rust-free stainless steel AISI 201 (1.4372) Width Thickness C403 9.5 mm ( 3 / 8 “) 0.64 mm 3335 N C404 12.7 mm ( 1 / 2 “) 0.76 mm 5340 N C405 15.9 mm ( 5 / 8 “) 0.76 mm 6675 N C406 19.1 mm ( 3 / 4 “) 0.76 mm 8010 N * packing unit: 100 unit Band-It tapes Type 316 C453 C454 C455 C456 Application: For all applications where high corrosion resistance is required Assembly tool: C001, C003 (can be found on page 241) Materials: Rust-free stainl. steel AISI 316 w/ fully rounded edges and high corrosion resistance Especially corrosion resistant! Type strap* Tearing forces Type tape (30.5 m roller) Type strap* Type strap* Tearing forces Tearing forces Packing unit Container colour Type tape (30.5 m roller) carton Type tape (30.5 m roller) KU container Type tape (30.5 m roller) Application: For high loading, e.g. hose connections, tube fixations where high loading occurs Assembly tool: C001, C003 (can be found on page 241) Materials: Rust-free stainless steel AISI 201with fully rounded edges and high tensile strength (about 25% higher than AISI 316) Advantages: Ÿ More stable than "normal" V2A with similar corrosion resistance – easily formed Ÿ Patented imprint allows specific cutting to length of the strap and avoids waste Ÿ Can be supplied in practical plastic container 240 APH Techniek BV - Wateringen - T +31 (0)174 219 200 - sales@aphtechniek.nl - www.aphtechniek.nl