APH techniek

All data are considered to be unbinding reference values. We accept no liability for data selection that is not confirmed in writing. Pressure data refer, if not otherwise indicated, to liquids of Group II at +20°C. 4 AISI 304 (> 70 mm) Hose clamps Type SSSi 80 ES 50 - 80 SSSi 110 ES 80 - 110 SSSi 140 ES 110 - 140 Safety hose clamps with optical overload protection Band width 12 mm Materials: Tape and housing: AISI 304, screw: AISI 303 This new type of safety hose clamp is opened fully by the quick fastener for pretensioning and prepositioning. An optical overload protection reliably displays any impending overload. Open lock and position tape. 1. 2. 3. Close lock. Tighten and finish. Type SSSi 170 ES 140 - 170 SSSi 200 ES 170 - 200 SSSi 230 ES 200 - 230 Screw locks and hand locks with tension tapes (10 and 18 mm tape width) screw lock hand retention lock Assembly with a screw lock: ...clip screw lock and fold back approx. 3 cm behind the main tape... ...place around the hose... ...place around the hose and clip into safety hinge,... ...tighten and finish. Measure tape and cut approx. 10 cm longer than hose coil... Type AISI 304 Screw lock 10 mm SSS 40/10 ES 40 - 100 SSS 100/10 ES Over 100 Hand retention lock 10 mm SSH 35/10 ES 35 - 60 SSH 60/10 ES Over 60 10 mm width Type AISI 304 Clamping band roller 10 mm wide SSKB 10/10 ES 10 m SSKB 20/10 ES 20 m Type AISI 304 Screw lock 18 mm SSS 80/18 ES 80 - 150 SSS 150/18 ES Over 150 18 mm width Type AISI 304 Clamping band roller 18 mm wide SSKB 10/18 ES 10 m SSKB 20/18 ES 20 m SSDS 16 ES SSDS 16 13 - 16 SSDS 18 ES SSDS 18 15 - 18 SSDS 21 ES SSDS 21 18 - 21 SSDS 23 ES SSDS 23 20 - 23 SSDS 25 ES SSDS 25 22 - 25 SSDS 27 ES SSDS 27 24 - 27 SSDS 31 ES SSDS 31 27 - 31 SSDS 35 ES SSDS 35 31 - 35 SSDS 37 ES SSDS 37 33 - 37 SSDS 40 ES SSDS 40 35 - 40 SSDS 43 ES SSDS 43 38 - 43 SSDS 48 ES SSDS 48 43 - 48 SSDS 50 ES SSDS 50 45 - 50 SSDS 55 ES SSDS 55 49 - 55 SSDS 60 ES SSDS 60 54 - 60 SSDS 65 ES SSDS 65 59 - 65 SSDS 70 ES SSDS 70 65 - 70 SSDS 75 ES SSDS 75 70 - 75 SSDS 80 ES SSDS 80 75 - 80 SSDS 85 ES --- 80 - 85 SSDS 90 ES --- 84 - 90 SSDS 100 ES --- 92 - 100 Wire hose clamps for mounting hoses with spiral inlay SSDS 110 ES --- 100 - 110 SSDS 115 ES --- 105 - 115 SSDS 120 ES --- 110 - 120 SSDS 125 ES --- 115 - 125 SSDS 130 ES --- 120 - 130 SSDS 140 ES --- 130 - 140 SSDS 150 ES --- 140 - 150 SSDS 160 ES --- 153 - 160 SSDS 165 ES --- 158 - 165 SSDS 170 ES --- 163 - 170 SSDS 180 ES --- 173 - 180 SSDS 185 ES --- 178 - 185 SSDS 195 ES --- 185 - 195 SSDS 208 ES --- 195 - 208 SSDS 260 ES --- 247 - 260 SSDS 270 ES --- 257 - 270 SSDS 315 ES --- 302 - 315 SSDS 360 ES --- 347 - 360 SSDS 413 ES --- 400 - 413 SSDS 450 ES --- 437 - 450 SSDS 500 ES --- 487 - 500 AISI 304 (< 70 mm) ...clip hand retention lock and fold back approx. 3 cm behind the main tape, place around the hose and... ...place around the hose... ... clip into safety hinge, tighten and... ...finished. Measure tape and cut approx. 10 cm longer than hose coil... Assembly with a manual turnbuckle: Ø Clamping range Ø Clamping range Type zinc- plated steel Type AISI 304 Type zinc- plated steel Type AISI 304 Ø Clamping range Ø Clamping range Ø Clamping range Ø Clamping range Roller length Roller length 238 APH Techniek BV - Wateringen - T +31 (0)174 219 200 - sales@aphtechniek.nl - www.aphtechniek.nl